Changed Washer on Tub Faucet a Week Ago Leaking Again
How to Fix a Leaking Bathtub Faucet
This simple DIY repair saves money and h2o. Learn how to set a leaky bathtub faucet.
Time
A full day
Complexity
Intermediate
Cost
$51–100
Introduction
You don't have to put up with the irksome drip from a leaky faucet, nor with the growing stain information technology oftentimes leaves in the tub or shower. Fix it at present and you lot'll prevent those headaches and save on yous water neb too. The entire job, with special tools, may prepare you lot back a bit of greenbacks, but doing information technology yourself is a lot cheaper than hiring a plumber, and ordinarily much cheaper and easier than tearing out the old faucet and installing a new 1.
Worn rubber washers, seals or gaskets in the valve assembly cause most leaks. Hither we'll show you lot how to prepare a stalk-type valve, which is common in older, two-handle faucets (separate hot and common cold). We won't embrace single-handle faucets here.
Tools Required
Materials Required
- Plumber's grease
- Stem valve repair parts
Make certain you accept new parts available
The first step for bathtub faucet repair is to brand certain y'all have the new parts that you need. You can fix nigh bathtub plumbing problems with the replacement parts bachelor at hardware stores and dwelling centers. A plumbing parts distributor will acquit a much larger pick and may exist able to special-order difficult-to-find items. There are thousands of different faucet replacement parts available to fix a leaky bathtub faucet, and then bring your one-time parts to the shop for a proper match to gear up a leaky bathtub faucet. If your valve is highly corroded or the finish is wearing off, supersede the entire faucet. Save money by doing uncomplicated plumbing repairs yourself. These plumbing fixes are completely DIY with basic tools and skills.
Project pace-past-footstep (6)
Stride 1
Disassemble the faucet: Pry off the handle insert
Removing the faucet handle is the toughest part of the job. Over fourth dimension, corrosion can about weld the handle to the stem. Shut off the water supply to the faucet and open up the valves to drain excess water from the organization. Pry off the handle insert with the sparse blade of a pocketknife.
Step 2
Bathtub Handle Replacement: Remove the Handle Screw
Remove the handle screw. Then wiggle the handle and pull it off. If the handle doesn't come off, heat it with a hair dryer to free it. Be careful; if you pull too hard, it'll break.
Step iii
Bathtub Handle Replacement: Pop loose the handle
If the handle won't come off, don't force it-it might break. Instead, remove information technology with a special handle puller. Turn the handle screw about halfway back into the stem. Position the handle puller's post against the screwhead and printing the arms together behind the handle. Turn the post clockwise until the handle pops loose. Remove the handle spiral and handle. Then pull off or unscrew the escutcheon plate.
Step iv
Bathtub Handle Replacement: Remove the stem
Once the handles off, unscrew the escutcheon and stem associates (Run across Figure A below). The stalk assembly controls the amount and temperature of the water dispensed through the tub spout or shower head. Remove it with a special bath socket wrench, which looks like a spark plug wrench on steroids.
Slide the bath socket onto the stalk bonnet and plow information technology counterclockwise to interruption the stem loose. If it sticks, soak it with penetrating lubricant. Unscrew and remove the stem.
Step five
Utilise a seat wrench
Leaks usually occur for two reasons. Over time, the seat washer stiffens and won't seal tightly. And water pressure gradually erodes the contumely rim of the seat. Supplant the seat using a special seat wrench.
Press the seat wrench firmly into the center of the seat. Plow counterclockwise to snap the seat loose and remove it. If it sticks, soak it with penetrating lubricant. Glaze the threads of the new seat with pipe dope and spiral it into the fixture trunk with the seat wrench.
Step half-dozen
Supervene upon the faucet stem parts
Figure A: Bathtub faucet parts names, faucet stem assemble and replacement parts
Fig. A shows the bathtub plumbing faucet stem replacement parts and how to set the stem for reinstallation. Lubricate the parts with special plumber's grease. If you're working on a 2-handled faucet, nosotros recommend replacing the washers and seats in both the hot and cold valves.
- Offset, unscrew the packing nut. Twist the stem clockwise and dorsum information technology out of the bonnet. Pry out the erstwhile packing washer with a small flat-blade screwdriver or option. Grease the stem threads and reinstall the stem in the bonnet. Grease the new packing washer and slide it in place, and so grease the packing nut threads and firmly tighten the packing nut. Use special plumber's grease.
- 2nd, remove the old seat washer screw and the old seat washer. Grease the new seat washer and the threads of the new spiral and then reinstall them.
- Tertiary, pull off the former bonnet washer, grease the new 1 and slide it in identify.
- Fourth, apply piping joint compound to the bonnet threads and reinstall information technology in the faucet trunk (Step 4).
- Five, grease the handle splines and supervene upon the escutcheon and handle.
Pitiful to burst your chimera, simply you need to terminate assertive these 10 plumbing myths ASAP!
Originally Published: November xix, 2019
Source: https://www.familyhandyman.com/project/how-to-repair-a-leaking-tub-faucet/
Post a Comment for "Changed Washer on Tub Faucet a Week Ago Leaking Again"